Estimating Material Properties for Fire Modeling |

## Issue 42: Estimating Material Properties for Fire ModelingBy Marc Janssens, Ph.D., FSFPE INTRODUCTION In a paper published more than 10 years ago, Babrauskas examined the question whether compartment fire models were good enough for Fire Safety Engineering (FSE). METHODS TO PREDICT THE PYROLYSIS RATE OF A SOLID Different approaches have been used to predict the onset (ignition) and rate of pyrolysis of a solid exposed in a compartment fire. Pyrolysis models can be grouped into four distinct categories based on the complexity of the model equations and the input data that are needed. Empirical Models The most basic approach to predict the burning rate in a room fire is based on the assumption that the material behaves in the room as it does at a specified heat flux level in a bench-scale calorimeter such as the Cone Calorimeter or the Fire Propagation Apparatus. The method developed by Wickstrm and Gransson to predict fire growth in the standard ISO 9705 room/corner test is a good example of this approach. The empirical approach can be refined by using mass loss rate Simple Analytical Models A slightly more complicated approach determines the surface temperature of the material as a function of time based on (1) a simplified analytical solution of the one-dimensional transient heat conduction equation for a constant heat flux at the exposed surface, and (2) Duhamel's superposition theorem to account for changes in the heat flux as a function of time. The rate of surface temperature increase at a specified heat flux is a function of the thermal inertia of the material for the thermally thick (semi-infinite) case. The rate depends on the product of the thickness, density and specific heat capacity of the material for the thermally thin case. The material is assumed to ignite once the surface temperature reaches a critical value. Following ignition the surface temperature is assumed to remain constant and the burning rate is determined from the net heat flux at the exposed surface and the heat of gasification of the material. Comprehensive Pyrolysis Models without Kinetics Modeling of the condensed phase is greatly simplified if it is assumed that the conversion to volatiles and a solid residue (the latter for char-forming materials) occurs abruptly at a specified "pyrolysis temperature". One-dimensional pyrolysis can then be simulated as a phase-change problem using an integral model. Comprehensive Pyrolysis Models with Kinetics The pyrolysis models in this category are similar to those described in the previous section. The primary difference is that the pyrolysis is described as one or a combination of several finite rate reactions. Pyrolysis models in this category have several advantages. For example, they can be used to account for temperature effects on the thermal properties and to model the heat transfer in and pyrolysis of multi-layer three-dimensional objects. The trade-off is that additional testing is needed (typically thermogravimetric analysis) to obtain the kinetic parameters (reaction order, pre-exponential factor and activation energy) for each of the reactions. NIST GRANT AND SFPE GUIDE A detailed standard guide to instruct fire model users on how to obtain material input parameters consistent with pyrolysis model assumptions would be extremely helpful to the fire protection engineering community and would greatly facilitate consistent application of computer models. Numerous approaches to obtain material parameters for input into deterministic fire models have been published in the literature. A subset of these approaches is described in ASTM E 1591 Standard Guide for Obtaining Data for Deterministic Fire Models. Recognizing the importance and urgent need, the National Institute of Standards and Technology decided to fund the development of a new comprehensive guide. A grant was awarded to Worcester Polytechnic Institute (WPI) to lead this effort. WPI is supported by Southwest Research Institute (SwRI) and SFPE. A three-year project was initiated on July 1, 2008 and aims at developing a document that will serve as the basis for an SFPE guide on obtaining material properties for pyrolysis modeling. It is anticipated that a task group will be formed in 2011 to develop this guide. Marc Janssens is with Southwest Research Institute. References - Babrauskas, V., "Fire Modeling Tools for FSE: Are They Good Enough?" Journal of Fire Protection Engineering, vol. 8, pp. 87-96, 1996.
- Wickström, U. and Göransson, U., "Full-Scale/Bench-Scale Correlations of Wall and Ceiling Linings," Fire and Materials, vol. 16, pp. 15-22, 1992.
- Babrauskas, V., "Specimen Heat Fluxes for Bench-Scale Heat Release Rate Testing," Fire and Materials, vol. 19, pp. 243-252, 1995.
- Mitler, H., "Predicting the Spread Rates of Fires on Vertical Surfaces," in Twenty-Third Symposium (International) on Combustion, The Combustion Institute, Pittsburgh, PA, 1991, pp. 1715-1721.
- Smith, E. and Green, T., "Release Rate Tests for a Mathematical Model," in Mathematical Modeling of Fires, ASTM STP 983, American Society for Testing and Materials, West Conshohocken, PA, 1987, pp. 7-20.
- Dillon, S., Kim, W. and Quintiere J,, "Determination of Properties and the Prediction of the Energy Release Rate of Materials in the ISO 9705 Room-Corner Test," National Institute of Standards and Technology, Gaithersburg, MD, NIST-GCR-98-753, 1998.
- Theuns, E., Merci, B., Vierendeels, J. and Vandevelde, P., "Extension and Evaluation of the Integral Model for Transient Pyrolysis of Charring Materials," Fire and Materials, vol. 29, pp. 195–212, 2005,
- Lautenberger, C., "A Generalized Pyrolysis Model for Combustible Solids." Ph.D. Thesis, University of California Berkeley, 2007.
- ASTM E 1591, American Society for Testing and Materials, West Conshohocken, PA, 2007.
For questions concerning delivery of this e-Newsletter, please contact our Customer Service Department at (216) 931-9934 or magazine.sfpe.org. |

Latest News
more

Membership Software Powered by YourMembership :: Legal